Every line has a purpose

LOUEIMetal Arts
A grey block bolted to aluminum extrusions and fitted around a steel rod holds a blue sensor on a machine frame, a black cable looping past it.

A custom 3D printed enclosure, made to fit what you have

Enclosures, housings and brackets, 3D printed by LOUEI 3D PRINT to fit what you own. Send sizes and a photo for a free review; no CAD needed. A person replies within one business day.

Send sizes and a photo What to measure

How do I get a custom enclosure made?

Measure what the enclosure has to fit: its size in more than one place, where each opening and mounting point sits, and what must stay reachable. Send those sizes and a ruler photo to LOUEI 3D PRINT, and say how the lid closes. If anything is missing, we ask before anything is made. Production starts only when you approve a plan.

  • Enclosures and housings
  • Brackets and mounts
  • Adapters and spacers

Around, onto or into: the three ways a part attaches

A part goes around something, bolts onto it, or takes something into it. Most are one of these, and what you measure changes with each. Not sure which? Say so in your message.

  • Around

    A black ribbed cap sits over the end of a grey metal tube on a diamond-plate deck, beside a coiled black hose and a worn wrench.
    Black cap on a grey tube end
  • Onto

    A green cone with a flanged base is held by two strap clamps on a chip-covered mill table, just behind a machine vise.
    Green flanged cone clamped on a mill table
  • Into

    A green tray with round and slotted holes holds five pink ceramic cups and seven copper collets in an open steel tool chest drawer.
    Green tray holding ceramic cups and copper collets

Start from what you have

Pick the one closest to what is on your bench.

Custom enclosures for a circuit board, sensor or controller

A custom enclosure is often for a board or a small device. Send these, and name any standard the box has to meet.

  • The board outline and the mounting-hole positions
  • The height of the tallest part
  • Every connector or button that must stay reachable, and where the cable leaves
  • Whether the lid screws on or clips on
  • Whether it needs vent slots
A cream collar screwed around a white downspout sits above a grey elbow, a brass fitting and a green hose dropping into a rain barrel lid.
Cream collar and elbow on a downspout
A blue cup holds a black corded computer mouse on a grey machine enclosure, with orange pallet racking behind.
Blue cup on a grey machine enclosure

How to measure for a part that has to fit

Measure the object the part has to fit, not the part itself. The right numbers tell us what to ask. Photograph the object straight on with a ruler flat beside it, then from the side.

What to send for each kind of part, to fit what you already have
PartHow it joinsWhat to sendSay it in words
Enclosure or housingAround what goes insideOverall size in more than one place, every opening, how the thing is held inWhich faces touch, which lift off, where it needs room
Box for a board or sensorAround the board, onto its mounting holesBoard outline, mounting-hole positions, height of the tallest part, every connector or button, where the cable leavesWhether the lid screws on or clips on, and whether it needs vent slots
Bracket or mountOnto a surfaceHole size and spacing, centre to centre, the shape of the surface, photos from the sideWhich way it pulls and what it carries
Adapter plateOnto two hole patternsEach hole pattern, centre to centre, and each outlineWhich side stays fixed
Spacer or standoffOnto a screw, across a gapOuter size, hole size, the gap, the screws usedWhether anything pulls along its length
Pocket or holderInto it: something sits insideThe size of what goes in, in more than one place, how deep it sits, and where a cable leavesWhat keeps it in place and how it comes out

Measure in mm or inches, in more than one place, and if the numbers differ, write down both. If a shape is too curved for a ruler, say so and send more photos. 3D scanning the object it has to fit is another way in, if that object can travel.

A few words do more than a decimal.

How to describe a fit: touch, slide or room

For every face that matters, pick one word and write it next to the size.

Say which holes a screw has to bite and which it only has to pass through.

  • Touch it sits hard against that face or presses in
  • Slide it goes on and comes off without a fight
  • Room it has to clear that face, with air between them

Send your sizes

Red jaw covers with notched faces line a worn, rusty bench vise gripping an aluminum rod on a cluttered workshop bench.
Red jaw covers on a worn bench vise

What happens after you send the sizes

Custom enclosures, brackets and mounts all start the same way: one message from you, then a reply from a person. For the whole route, see how a project runs with us.

  1. 1

    Send what you have

    Sizes, a photo or a file. Add how it attaches, what it carries, where it lives and how many.

  2. 2

    A person reads it

    We reply with the next step, or with what we still need.

  3. 3

    You answer the questions

    Answer what we ask and nothing more. A rough guess is fine; say it is a guess.

  4. 4

    You approve a plan

    Raise any doubt before you approve a plan. Production waits for your yes.

Send a photo and the sizes

Enclosures, brackets and adapters

Call it what you like. Most fitted parts are one of these three.

  • Two grey boxy housings are fixed under the steel roof of a machine's work area, above a cutting tool standing in a holder among metal chips.
    Two grey housings under a machine roof

    Enclosures and housings

    A stock box is rarely the right size, and its holes are in someone else's places. Tell us what goes inside and what has to stay reachable, like a lid or a screw head. Already have the file and only need it printed? Start with our custom 3D printing service.

  • An orange bracket wraps a galvanized square post and holds a black box, with a black cable running past it beside a timber garden bed.
    Orange bracket on a galvanized post

    Brackets and mounts

    Two surfaces, one custom bracket. Send the hole spacing on each side and say what is in the way: a rib, a lip, a bolt head a wrench has to reach. Did the old one break? See a replacement for a broken or discontinued part.

  • An orange block is bolted to the side of a pale blue machine, with a polished steel rod passing through it.
    Orange block on a pale blue machine

    Adapter plates and spacers

    An adapter plate has two hole patterns to get right, one on each face. A spacer or standoff holds two things a set distance apart: send the gap and the screw. If it holds the work and does not stay on the machine, it is a jig or fixture for your shop.

Can you make a part from a design file I already have?

Already have a file? Send it.

Yes. We accept STEP, STL, OBJ, IGES, DXF, PDF drawings and photographs, so a file from a freelancer or a designer can be where this begins.

We read it and tell you what happens next or what is still missing.

Send the file

Two yellow curved gripper fingers are bolted to a black parallel gripper on a blue rotary robot wrist standing on a steel machine-shop bench.
Yellow gripper fingers on a blue robot wrist

Plastic or steel: what decides it

Say what it carries, which way it pulls and what would happen if it let go. Direction comes before material.

After direction comes material: FDM materials and how they differ shows what each plastic does.

If a part may need to be steel, ask about steel through LOUEI Metal Arts, our sister company: two companies, one team, one quote. We tell you whether they can take it. CNC machining coming soon, not offered yet.

What we will not promise

Better to know these before you measure anything.

  • We print plastic only, in FDM and resin. We do not print metal here.
  • Some parts need a certification we do not hold, and we say so.

Written by the LOUEI 3D PRINT team. Last updated 9 November 2026.

Before you send the sizes

Can I get a custom enclosure made from just my measurements?

Yes, to start, and CAD design is part of the job. Send the sizes, the hole spacing and the faces that touch something. Numbers alone cannot promise a fit, so we ask about whatever is missing first.

Does the enclosure meet a standard I have to follow?

Do not assume it does. Printing an enclosure does not make it meet a standard. Name the standard or mark in your message, and we tell you whether we can take the job.

Will a bracket carry the weight I need?

A bracket's load depends on its shape, its material and which way it is pulled, and we cannot promise a figure. A yes from us means we can make it, not that it will carry the weight. Tell us the weight and what happens if it lets go. If it may need to be steel, we tell you whether LOUEI Metal Arts can take it.

How close can you hold my dimensions?

Long thin parts are harder to hold to size than compact ones, and the process and material matter too, so no one figure fits every part. Circle the sizes that matter most and say which faces touch, slide or need room.

Can I order just one?

Yes. A single housing, or one bracket before you order more, is normal work for us. If you need ten or more, say so in your message: bulk runs from 10 to 10,000 parts are priced by volume.

How long will it take and what will it cost?

The review tells you what decides how long it takes. Price depends on the part's function, the process, the material and the quantity, and it is confirmed before production. The review is free, and you owe nothing unless you approve a plan.

Will a custom enclosure work outdoors?

Where the part lives helps decide the material, so say so in your message. For the plastics we print, see FDM materials and how they differ.

Who owns the drawing you make?

Confidentiality and file ownership are agreed per project, in writing, on request. Say what you need for this part before you approve a plan.

A bright blue box-shaped cover wraps the lower end of the head on an old green milling machine, above its table in a workshop.
Blue box cover on an old green milling machine

Send the sizes of what it has to fit

One size and a ruler photo is a real first message.

Serving North America. Shipping is arranged per project.

Send sizes and a photo Ask a question first

Free review · A person reads every project · No CAD needed

Get a quote
LOUEI 3D PRINT

Get a quote

Tell us what you need — the review is free, and a person replies within one business day.

Opens your email app with everything filled in.