Every line has a purpose

LOUEIMetal Arts
Flat orange straps, each with a ring at one end and a short hollow post at the other, lie jumbled on a scarred wooden bench.

More than one of the same part: 3D print it or cast it

Print each one while the design could still change. Cast from a silicone mould when it must be plaster or cement, or when the mould can be spread over enough copies. Tell us the part and how many.

Send a photo and a number Which route suits it?

The second one is the real decision

Order one, try it where it has to work, order the rest.

One-off parts are normal work. So you can order one, try it on the real job, and decide on the rest with it in your hand.

Those are two orders, each priced on its own, and the first does not commit you to the second. Two orders may not match in colour, and if the part has to be cast, a mould has to be made for that first one, so ask how it is priced.

One first makes the most sense when fit is the doubt and the rest can wait. Tell us what on the first one has to carry over to the rest, and the review tells you whether one first suits yours.

Ask about one part first

Dark grey square blocks sit on aluminum rails on a worn wooden bench, with one block lying loose and a U-shaped bracket to the right.
Dark grey blocks on aluminum rails on a wooden bench

Should I 3D print or cast a small run of the same part?

LOUEI 3D PRINT does both: FDM or resin printing and silicone mould casting. A printed run needs no mould. Casting needs an original and a mould before the first copy, and that cost has to be spread over enough copies to pay its way. Plaster and cement cannot be printed here, filament plastics are not cast, and resin can go either way.

  • Printed or cast
  • Start with just one
  • Resin, urethane, plaster or cement

What you need to start a small run

Any of these is enough to begin.

A set of the same part

We can make a set of the same discontinued part, not just one. Send photos or a file, say how many, and say what has to match, such as hole spacing or fit. Some parts cannot be reproduced, and the free review says so.

  • The rest of a discontinued set

    You found a couple of the drawer pulls and still need the others. Photograph the least worn one beside a ruler, say how many are missing, and what each one sits on.

  • A run for a club or registry

    A group buy for a vintage bike or car club. Say who designed the part and whether members pay for it. Someone else's design or a logo needs a person to look before we can say yes.

    who may copy a part someone else designed

  • A small run of your own design

    For a market table or a small product. Say if the design could still change, because that alone can decide the route.

Small parts that come in sets

One clear photo of one part beside a ruler is enough to start.

  • White links with a ring at each end lie scattered on a pale wooden bench beside a white tray with rows of shaped recesses.
    White double-ring links beside a tray on a pale bench
  • A yellow spur gear with a toothed bore sits on the gold textured build plate of a desktop printer, with pliers on the bench nearby.
    Yellow spur gear on a gold build plate
  • A grey ribbed channel lies on a worn wooden bench beside the two open halves of a translucent mould with a ribbed hollow.
    Grey ribbed channel beside an open translucent mould

From a rough number to a route and a price

A rough number is enough. The review is free, and you owe nothing unless you approve a plan and production begins.

  1. 1

    Send a photo and a number

    Or the file. If you are weighing two quantities, give both, and say what has to match.

  2. 2

    Add what we need to know

    What the parts do, any date you have, whose design it is, whether it carries a logo, and whether these will be sold.

  3. 3

    A person reads it

    A reply comes within one business day, with any questions we need answered.

  4. 4

    The route and the price

    We name the route that suits it and what it will cost.

Tell us how many

What has to stay the same from part to part

Hole spacing, fit on the part it meets, colour and surface look are separate things. Tell us which ones must match.

Every run has small differences from part to part, and long thin shapes tend to vary more than compact ones, so we will not promise every one comes out the same. The review says whether we can make it.

Reorder the same part, even one made elsewhere

You can order the same part again later, and repeat orders keep the project information. A reorder runs the same way as a first order: send what you still have from the last one, the order details, the file or a photo, and say what changes this time.

If another shop made it, we can look at that too once you say whose design it is. It starts as a new job, from whatever you can send.

Grey and orange bins fill an open tool-chest drawer, holding screwdrivers, drill bits and cable ties, with several bins empty.
Grey and orange bins in an open tool-chest drawer
Five black slotted covers fill the bays of a black rack-mounted unit, beside a silver drive tray with a small green light.
Five black slotted covers in a rack-mounted unit

When a few becomes a lot

Send the number you actually need, and mention a bigger one if it might follow.

For a bigger order, bulk runs from 10 to 10,000 parts are priced by volume and have their own page.

What a run cannot promise

Better to hear these before you plan around them.

  • Some parts cannot be reproduced: badly damaged, missing geometry, certification we do not hold.
  • FDM and resin only. We do not do SLS, MJF or metal printing here.

Written by the LOUEI 3D PRINT team. Last updated 9 November 2026.

Before you commit to a number

Is a mould worth it for only a few parts?

Often not, unless the part has to be plaster or cement. A mould has to be made however few you pour, and how many copies one mould gives depends on the part.

Does the price change with the quantity?

Price depends on the part's function, the process, the material and the quantity, and it is confirmed before production. The review is free, and you owe nothing unless you approve a plan. How far the number moves it for your part, the review says.

Is there a minimum?

A single cast part carries a whole mould and a printed one does not, so a low number usually points to printing. Put the number you want in your message, even if it is one, and we will say what suits your part.

How do repeat orders work?

It is a new order for a part you have had made. Say whether you want the same number, more, or a change, because a different number can change the route and the price.

Will a later batch be the same colour?

We cannot promise that. If colour matters, say so when you first write, and we will say what we can do for your set.

What happens to the mould afterwards?

Ask before you approve anything, and we will tell you how that mould is priced and what happens to it after your run.

Can you make more of a part another shop made for me?

We can look at it, as a new job, and a file gives us more to go on than a photo. Confidentiality and file ownership are agreed per project, in writing, on request, so mention any conditions that shop's work came with.

I plan to sell these. Does that change anything?

It can. A bigger run does not make someone else's design yours to sell. If the part carries a logo or another maker's name, say so when you write.

How long does a small run take?

Part size, the number and the route all move the time, and a cast run also waits on its mould. Casting depends on the size of the job. Give us any date you have, and the review tells you what decides it for yours.

A long, flat black part, tapered at one end and stepped at the other, lies under the nozzle of an open-frame printer beside filament spools.
Long flat part on an open-frame printer bed

Say how many

Send a photo or the file, and say how many, even a rough guess. If you are torn between one and the rest, say so.

We are a custom 3D printing company. We print in FDM and resin, and make silicone moulds with copies in resin, urethane, plaster or cement. More about us.

Shipping is arranged per project, so say where the parts are going.

Send a photo and a number Ask a question first

Small runs of the same part, 3D printed or cast · Silicone moulds · Serving North America

Get a quote
LOUEI 3D PRINT

Get a quote

Tell us what you need — the review is free, and a person replies within one business day.

Opens your email app with everything filled in.