Every line has a purpose

LOUEIMetal Arts

Broken part, no drawing: what to measure and send a shop

The form says ‘upload your CAD file.’ Your CAD file is in a drawer, in two pieces.

Short answer

To measure a part for replacement, write down only the sizes that decide fit: the overall size, each hole or bore, the spacing between them, and the size of whatever the part fits onto. Where the old part is worn, measure the part it fits instead. Then add six photos, with a ruler or coin beside the part in two of them, to show what numbers cannot.

Go to the sheet Send a photo of the part

LOUEI 3D PRINT team Updated November 12, 2026 9 min read

A grey ribbed bracket plate held by small screws around a rusty shaft, next to a worn bearing housing on a scarred steel plate, with parts bins and a coil of wire behind.
A ribbed bracket plate bolted beside a shaft bearing on an old steel machine, marked in white: 1 a rib on the plate, 2 the shaft, 3 the worn bearing housing.

The sheet

One page for paper, not a form on this screen: nothing here is sent. Print it or copy it by hand, fill it in beside the part, then photograph the sheet with your other photos. Blank boxes are fine. The marked entries are an example.

Print the sheet (1 page)

  1. 1 Sketch or trace the part

    Lay the part flat on the sheet and draw round it, or sketch its outline, and mark which side faces up. You do not need to know what the part is called, or have any CAD drawing, to fill this in or to get a replacement made from your broken part. A rough outline is enough: it shows which shape the numbers belong to.

  2. 2 Measure the outside

    Write the longest length, the width, the height and the thickness at the thinnest wall. Put the unit beside every number, and note what you measured with: ruler, tape or calipers.

  3. 3 Measure the holes

    For each hole, write its diameter, the distance from its centre to the nearest edge, and the distance to the next hole. If a hole is worn, measure the pin, screw or shaft that goes through it instead (see the worn-hole drawing below).

  4. 4 Note what it fits and where it lives

    Write what the part fits onto or into. Then tick what applies: indoors, outdoors, gets wet, gets warm, carries weight.

  5. 5 Take the six photos

    Take the six views drawn below and tick each one on the sheet. Shoot straight down where you can, in even light, with the whole part in the frame.

Measure-and-photo sheet

Example, marked

Partshelf bracket

  • Units
  • Ticked: mm
  • inch
  • Start where you are
  • Ticked: Whole part
  • Pieces
  • Photos only

1Sketch or trace the part

this side up

2Measure the outside

SizeMeasurement
Overall length120
Width78
Height98
Thinnest wall8

3Measure the holes

HoleDiameterCentre to edgeTo next hole
192276
2922
3

4Note what it fits and where it lives

Fits onto or intoa shelf rail, two studs

  • Ticked: Indoors
  • Outdoors
  • Gets wet
  • Gets warm
  • Ticked: Carries weight

5Take the six photos

  • Ticked: From above, on plain paper
  • Ticked: Same view, with a ruler
  • Ticked: Same view, with a coin
  • The break, close up
  • The part in place
  • The part it fits

Measure-and-photo sheet · LOUEI 3D PRINT

Six photos a shop can use.

From above, on plain paper
Same view, with a ruler
Same view, with a coin
The break, close up
The part in place
The part it fits

What if your part is a knob, a clip or a hinge?

Whatever the part is, measure the sizes where it meets something else, and photograph the rest.

The drawing uses a bracket because its sizes are easy to see. Your part may look nothing like it, and that is fine: the table below shows what to measure and photograph on six kinds of part.

Line drawing of an L-shaped bracket with two holes, marked with the six sizes a shop asks for.125643FROM ABOVEFROM THE SIDE
  1. Overall length: the longest side, end to end.
  2. Width: across the part at its widest.
  3. Thickness: at the thinnest wall.
  4. Hole diameter: or the diameter of the screw or pin that goes through it.
  5. Centre to edge: from the middle of a hole to the nearest edge.
  6. Centre to centre: from the middle of one hole to the middle of the next.

The bracket is only an example. A knob, a clip or a coupling has its own version of these sizes, and the table lists them.

What to measure and what to photograph on a broken part with no drawing, by kind of part. Measure the sizes that decide fit, and photograph the rest.
Kind of partMeasure thesePhotograph especially
Flat plate or bracketLength, width and thickness; each hole’s diameter; centre to nearest edge; centre to centreThe flat face from above on plain paper; the bend or edge from the side
Round part with a bore (knob, gear, wheel, coupling)Outside diameter; bore diameter, or the shaft it fits (across the round and across any flat); bore depth; thicknessThe face with a ruler; the bore from the front; any key slot, flat or teeth up close
Clip or snap-fitSlot or gap width; thickness of the arm; size of the edge or pin it grips; overall lengthThe clip at rest and flexed; the part it clips onto; the broken arm up close
Hinge or pivotPin or hole diameter; centre to centre between pivots; width of each arm; thicknessClosed and fully open; the pin; the parts either side, in place
Hollow part (cover, housing, cap)Outside length and width; wall thickness; inside depth; position and size of each screw hole and openingFrom above and from inside; the rim where it meets the other part
Curved or free-form part (handle, grip)Only the sizes where it meets something else: a hole, a mount, the overall lengthMany angles around the part, a ruler in frame; this shape may need a scan, not a ruler

A curved grip or a handle has few straight sizes to take. Measure where it meets something, photograph it from many angles, and see 3D scanning and reverse engineering.

How accurately do you need to measure?

How accurately you need to measure a part for replacement depends on what each size does.

Take the most care with a size that meets another part, such as a pin hole or a slot. Measure each size more than once and write down every reading with its unit, for example 11.9, 12.0 and 12.1 mm. Your readings and photos are what a shop starts from; if you can send the part itself, a shop can check them against it.

If your readings jump around, measure again in another spot: a worn or warped part may not be the same size all the way round.

This guide gives no figure for how close is close enough. That depends on the part, what it is made of and how it is made, so ask the shop about each size that must fit. A ruler or coin in two of your photos lets anyone check a number against the picture.

What if the hole is worn or the part is cracked?

If a hole is worn, measure the shaft or pin that goes through it; if the part is cracked, keep every piece and photograph the pieces laid together.

A worn hole is no longer the size it was made. So measure the shaft, pin or screw that goes through it as well, across the round, and across the flat if it has one. If that looks scored or worn too, say so in your note.

Measure what it fits, not only the worn part

A knob seen from behind: its hole is worn into a rough oval, larger than the dashed outline of the hole as it was made.?
A worn hole reads wrong: it is no longer the size it was made.
The end of a round shaft with one flat side, marked with two sizes: across the round and across the flat.AB
Measure the shaft it fits as well: across the round (A) and across the flat (B).

For a cracked or broken part, lay the pieces together the way they broke and photograph them as one part. Then photograph each piece alone, and the break close up. Keep every piece as it is, even the small ones: the pieces still show the wall, the holes and the shape your numbers came from. If a piece is lost, the part it fitted against, or a matching part from the other side, can show what is missing.

Can you send the broken part instead of measuring it?

Often you can, but ask the shop before you post anything, and fill in what you can of the sheet first.

At LOUEI 3D PRINT, the broken part itself is one of the ways to start, along with a photo, a sketch or your measurements.

Fill in the sheet before the part leaves your hands. Photos with a ruler give a shop something to look at before you post anything, and if the parcel goes astray, your numbers and photos are what is left.

If you do post it, send the part alone, with any battery, fluid or chemical taken out, and check your carrier’s rules first: Canada Post, for one, does not accept dangerous goods.

Before you contact any shop

Have these ready. Any shop will ask for most of them.

  • Photos: the whole part on plain paper, the same view with a ruler beside it, and the break up close.
  • The sizes you can measure, and what the part fits onto or into.
  • Where the part lives and what it does.
  • How many you need.
  • Any file or drawing you have, even an old one.

At LOUEI 3D PRINT you can start from anything: an idea, a sketch, a photo, CAD, measurements, the broken part itself or a previous order. We read STEP, STL, OBJ, IGES, DXF, PDF drawings and photographs.

When this is not a job for a shop

  • Some vehicle equipment is regulated by law in Canada, so a part that keeps a car safe is not a casual copy.
  • In BC, most gas and electrical work must be done by qualified people working for licensed contractors; a homeowner may do some of it, but only with a permit. So a broken part in a gas or mains-powered appliance is a question for a licensed contractor first.
  • A printed copy of a part that touches food carries no Canadian food-contact approval; Health Canada’s packaging page does not mention 3D printed kitchenware.

Some parts cannot be reproduced: parts that are badly damaged, parts with missing geometry, and parts that need a certification we do not hold.

Written by the LOUEI 3D PRINT team. LOUEI 3D PRINT makes custom and replacement parts: 3D scanning and reverse engineering, FDM and resin 3D printing, molding and casting. Serving North America.

Back to the blog

Get a quote
LOUEI 3D PRINT

Get a quote

Tell us what you need — the review is free, and a person replies within one business day.

Opens your email app with everything filled in.