Half the part is missing. Can it still be copied?
A part in flawless shape can still be one a good shop refuses to copy.
Short answer
To reconstruct a broken part for 3D printing, you need something that still shows the lost shape: the other half to mirror, the part it fits onto, the broken pieces, clear photos or an old drawing. With one or more of these, a copy is often possible. With none, it may not be. A part that keeps people safe may be refused even when it is whole.

What can still give the shape
A copy needs its shape from somewhere, and six things can still give it: the pieces, a whole half, a twin from the other side, the part it fits, old photos and an old drawing.
Go along the row and find what you still have. Each one is a way to try, not a promise: the more of them you hold, the less of the shape has to be guessed. The pieces count most when they are left as they broke, because the broken edges show how they line up and how thick the wall was.
Then answer the three questions under the drawings. They will not tell you yes or no for certain, but they show how much of your part is still there to copy. For your pieces today: keep them unglued in one bag, photograph them laid together and one by one with a ruler beside them, and keep the part they fit onto. You do not need a scan or a CAD file to ask: at LOUEI 3D PRINT, a project can start from a photo of the pieces.
What can still give a copy its shape
- Where it touched: can you see the faces where it met other parts, or do you still have the part it fits?
- A twin: is there a whole half, or the matching part from the other side?
- The wall: does a break show how thick the part was?
- Your reading: yes to all three: a rebuild is likely. A twin and little else: the twin may carry it, if both sides truly match. Mostly no: it may be a part a shop declines.
Can you copy the missing half from the other side?
The missing half of a broken part can be copied from the other side only if the part is truly symmetrical.
Before trusting a mirror, compare the two sides point by point: the holes, the clips, the ribs and any offsets or steps. The left and right parts of a pair often differ in small details, so a mirrored passenger-side part may not fit the driver’s side. Where the sides differ, the part it fits onto, or photos of the broken side in place, have to fill the gap.
One scanner maker’s guide works this way: it captures the other side’s part first, then rebuilds the details that belong only to the broken side. Use the drawing below to check your own part before you count on a mirror.
- Holes: the same distance from the centre line on both sides?
- Clips and ribs: the same ones, in the same places, on both sides?
- Offsets: does one side step up, down or out where the other does not?
- Wall: the same thickness on both sides, where a break lets you see it?
If any answer is no, that side cannot simply be mirrored.
What if the broken piece is gone completely?
If the broken piece is gone completely, the part it fitted onto can still show its holes, its mounting faces and the space it filled, and a new piece can be modelled around those.
One small print shop’s guide says the same: when the piece is gone but the part it bolted to survives, they model around the mounting features. It adds that an old service manual or exploded diagram helps a lot when it comes with a few measurements, and that photos with a ruler in the frame are less accurate than the part itself but enough for rough cosmetic pieces.
What the part it fits cannot give is a shape that touched nothing else, such as a lip, a curve or a grip. That shape has to be designed from the other clues, not measured. 3D scanning and reverse engineering can scan the pieces into editable CAD, along with the part they fit, and the lost shape is then drawn in around what survived.
| What survives | What it can give | What it cannot give |
|---|---|---|
| Mirror half | The whole outline, if both sides truly match | Details that differ left to right: clips, ribs, offsets |
| The part it fits | Hole positions, mounting faces and the space the lost piece filled | Any shape that touched nothing else |
| The pieces | Wall thickness and curve at the break, and every surface that survived | The shape of what is gone |
| Photos | The outline and how it sat in place, with a ruler in frame for scale | Sizes to trust for a tight fit |
| Old drawing | The intended shape and, where printed, its sizes | Wear, later changes, or sizes it leaves out |
Should you glue the pieces back together first?
No: keep the pieces as they broke, unglued and untouched, because the broken edges show how the pieces line up and how thick the wall was.
One scanner maker’s guide is plain about it: do not throw away pieces, alter the broken edges or glue the part before it is recorded. Glue covers the very edges that show where each piece belongs.
Lay the pieces together the way they broke and photograph them as one part. Then photograph each piece alone, the break close up, and the part in place or the gap where it sat. Keep every piece, even the small chips, together in one bag.
If the part is shiny, clear or plain with no texture, say so with your photos: a 2026 research preprint calls such surfaces notoriously challenging for scanning methods that work from many pictures.
Will the copy be exact where pieces were missing?
Where pieces of a broken part were missing, no one can promise the copy is exact.
Where a piece survives, its shape can be measured; where it is gone, the shape is rebuilt from the other clues, so it stays a careful guess until it is tried in place. The two drawings below show the difference. A careful maker records which areas were measured and which were rebuilt, and checks the fit, often with a first test piece, before calling the part done. Ask which areas were measured and which were rebuilt, and expect any change to land in the rebuilt areas.
A good rebuild does not copy the damage either. One reverse-engineering service’s guide warns that a model taken straight from a worn part copies its wear too, and says to work back to the shape the part was meant to have.
What is measured, what is guessed
Why would a shop refuse to copy a part?
A shop may refuse to copy a part when too little of it survives to show its shape, or when the part does a job where a copy of its shape is not enough evidence that it is safe.
That is why a part in flawless shape can still be turned down: when a part keeps people safe, a copy of its shape is not enough evidence on its own.
At the other end is the part with almost nothing left. One small print shop’s guide admits that a single sun-bleached fragment, with no mating part and no manual, sometimes cannot be recreated with confidence.
At LOUEI 3D PRINT, some parts cannot be reproduced: badly damaged, missing geometry, or certification we do not hold. Asking costs nothing: the review is free, and you owe nothing unless you approve a plan and production begins. The price comes from the part (what it does, how it is made, the material and how many) and is confirmed before production.
Before you contact any shop
Have these ready. Any shop will ask for most of them.
- Photos: the whole part on plain paper, the same view with a ruler beside it, and the break up close.
- The sizes you can measure, and what the part fits onto or into.
- Where the part lives and what it does.
- How many you need.
- Any file or drawing you have, even an old one.
At LOUEI 3D PRINT you can start from anything: an idea, a sketch, a photo, CAD, measurements, the broken part itself or a previous order. We read STEP, STL, OBJ, IGES, DXF, PDF drawings and photographs.
When this is not a job for a shop
- In Canada, the Motor Vehicle Safety Act sets standards for some vehicle equipment, so a part that keeps a car safe is not a casual copy.
- In BC, most gas and electrical work is for qualified people working for licensed contractors, so a broken part on that side of an appliance is a question for them first.
Some parts cannot be reproduced: parts that are badly damaged, parts with missing geometry, and parts that need a certification we do not hold.
Written by the LOUEI 3D PRINT team. LOUEI 3D PRINT makes custom and replacement parts: 3D scanning and reverse engineering, FDM and resin 3D printing, molding and casting. Serving North America.