Why a tiny custom part costs more than it looks
The plastic in your small part might fill a teaspoon. That’s rarely what the quote is for.
Short answer
Why is my 3D printed part so expensive? Usually the set-up, not the plastic: a small part is still a whole job, with a file to prepare and a machine to set up, however little plastic it takes. At LOUEI 3D PRINT the price comes from what the part must do, how it is made, the material and how many, and it is confirmed in the free review.

Anatomy of a quote
This sheet is for paper. Print it or copy it out, and fill it in with your own part in front of you; nothing on this screen is sent anywhere. The marked entries are one imagined example: a slotted vent disc for a dust port under a bench. Its four rows are the four things a LOUEI 3D PRINT price comes from: what the part must do, how it is made, the material and how many. Fill them in to see what affects the cost of a 3D printed part, and what to ask.
1 What it must do
Write one line on the part’s job: does it only sit in place, hold or carry something, or let air through? Add where it lives: indoors, under a bench, out in the sun. One machining trade column warns buyers that asking for more than a part needs can add cost.
2 How it is made
Tick the ways of making it you have asked about. LOUEI 3D PRINT prints in two ways only: FDM and resin. Ask any shop whether another way could do the same job. A guide to ordering custom parts warns that ignoring how a part will be made can raise its cost a lot.
3 What it is made of
Tick what the part must stand up to: heat, load, the outdoors, or none of these. The fewer boxes you tick, the more room there is to choose. If another material would do, say so: the same guide suggests telling the shop when you are flexible on material.
4 How many
Tick how many you need: just the one, one and a spare, or a few. Then ask the shop what one more copy changes. The set-up for a run is shared by every piece in it, so the price per piece usually falls when the same part is made in more copies.
Anatomy of a quote
Example, marked
1What it must do
- Only sits in place
- holds or carries
- Ticked: lets air through
Where it livesunder a bench, with dust and knocks
2How it is made
- Ticked: Asked which way of making it would do
Ways I asked aboutFDM print, resin print
3The material
- Must stand up to heat
- load
- the outdoors
- Ticked: none of these
None ticked: room to choose.
4How many
- Just the one
- Ticked: one and a spare
- a few
Ask what one more copy changes.
Anatomy of a quote · LOUEI 3D PRINT
Why doesn’t a smaller part cost less?
A small part still needs the file prepared and the machine set up, so its price does not fall in step with its size.
The plastic in a small part may really fill a teaspoon. But the file still has to be prepared, the machine set up and the run started, whether the part is the size of a coin or a shoe. Published cost models count that preparation time alongside machine time, labour and material. One quoting platform’s worked example puts labour, not filament, as most of the cost of a printed part.
A guide to ordering custom parts from a machine shop puts it plainly: a machine may make a part quickly and still take far longer to set up, which is why an order for one part can seem expensive. With one piece, that piece carries the whole set-up; with ten of the same piece on one plate, each carries a tenth of it. Past a certain count, each piece’s share of the set-up is small beside its own machine time and material, and a bigger run saves little more. The same arithmetic is why a mold is rarely the answer for one part: a mold is a one-time tool, shared by every part made in it.
At LOUEI 3D PRINT, one-off parts are normal work. The price comes from the part: its function, process, material and quantity, and bulk runs are priced by volume.
However small the part, it still goes through file preparation and set-up.
Why won’t a shop give a price before seeing the part?
A shop can only give a reliable price once it knows the part, because what the part must do, how it is made, the material and how many change from one part to the next.
A price posted on a web page has to assume a part: its job, its material, its count. Yours may differ on all of them. Shops differ too: one print broker’s blog notes that makers quote the same part differently, each with its own machines and costs, and that some add a margin when a part is risky to make.
That is why this page shows no price. At LOUEI 3D PRINT the price is confirmed in the free review, before production, and you owe nothing unless you approve a plan and production begins.
When any quote arrives, ask first which share is set-up (reading the request, preparing the file, setting up the machine) and which grows with each copy (machine time and material): that tells you what a second copy would add.
| Price factor | In plain words | What to tell the shop |
|---|---|---|
| What the part must do | Whether it carries a load, fits against another part, or only sits in place. | The job in one line, and what it touches. |
| How it is made | Printed in FDM or in resin. | Whether another way could do the job. |
| The material | The plastic the part is made from, chosen from the shop’s materials. | Where it is used, and whether there is room to choose. |
| How many | How many copies of the same part are made; bulk runs are priced by volume. | One, or a few, and whether the number may change. |
How can you bring down the price of a custom part?
To bring down the price of a custom part, ask for no more than the part needs in its job, its process, its material and its count, and ask the shop where there is room.
Four questions help. Must it carry a load, or only sit in place? Could another way of making it do the same job? Is there room to choose the material? Would it help to have a spare made now, rather than order again later? To the last one, expect to hear that a second copy in the same run often adds less than the first, because the set-up is already done.
One machining trade column asks buyers the same: are you asking for more precision than the part needs? Extra precision can add cost.
At LOUEI 3D PRINT you can ask them in the free review. See how FDM and resin parts get priced.
One copy, or a full plate
Should you look for an off-the-shelf part first?
Yes: if a stock part already does the job, buying it will usually cost less than having one made.
Search by what the part does and the size of the place it fits, not only by its name. Check whether the maker of the machine still sells it as a spare, and whether a near fit could be adapted. Even one print broker’s blog tells its own readers to look for an existing part before paying for a custom one.
If nothing fits, a custom part is the route; for a simple part that only sits in place, a printer of your own or a friend’s may also be a fair first try. LOUEI 3D PRINT can start from the broken part, a photo or measurements. Some parts cannot be reproduced, and the reply says so plainly.
Before you contact any shop
Have these ready. Any shop will ask for most of them.
- Photos: the whole part on plain paper, the same view with a ruler beside it, and the break up close.
- The sizes you can measure, and what the part fits onto or into.
- Where the part lives and what it does.
- How many you need.
- Any file or drawing you have, even an old one.
At LOUEI 3D PRINT you can start from anything: an idea, a sketch, a photo, CAD, measurements, the broken part itself or a previous order. We read STEP, STL, OBJ, IGES, DXF, PDF drawings and photographs.
When this is not a job for a shop
- If a stock part does the job, buy that instead: a custom part usually costs more than one off the shelf.
- In many cases a part made by additive manufacturing costs more than the same part made by traditional methods, a US national lab’s 2014 report found; for a long run of one design, ask about other processes.
- Some vehicle equipment is regulated by law in Canada, so a safety-critical car part is not a casual reprint.
Some parts cannot be reproduced: parts that are badly damaged, parts with missing geometry, and parts that need a certification we do not hold.
Written by the LOUEI 3D PRINT team. LOUEI 3D PRINT makes custom and replacement parts: 3D scanning and reverse engineering, FDM and resin 3D printing, molding and casting. Serving North America.