Every line has a purpose

LOUEIMetal Arts

Part discontinued? What to try before scrapping the machine

Don’t drag that machine to the curb yet. The maker that won’t sell you the part may still have the drawing.

Short answer

To find a replacement for a discontinued part, do not scrap the machine yet: there is an order to try first. Ask the maker for stock, a newer part number or a drawing. Look for an equivalent or a used part. Repair the old one, or have it made again from the broken part. Keep the broken part as it is: it is your evidence.

See the ladder Send a photo of the part

LOUEI 3D PRINT team Updated November 12, 2026 9 min read

Black vented cylinder sections joined by metal straps on an old green loom, with punched cards hanging on pins and a red roller in front.
Card-cylinder sections on an old green textile loom, marked in white: 1 the front black cylinder section, 2 the metal strap joining two sections, 3 punched cards hanging on pins below the cylinder.

The ladder

This is a page for paper. It is not a form, and nothing on this screen is sent. Copy it out or print it, then work down it one rung at a time. Stop at the first rung that solves it. Skip any box that does not apply. The entries are one example, a blower wheel; the rungs and checks are the same for any part.

Print the ladder (1 page)

  1. 1 Keep it and name it

    Keep the broken part and every piece as it is: do not glue, clean or throw it away. It is your best record of the shape and sizes. Photograph every number on the part and on the machine’s rating plate.

  2. 2 Ask the maker

    Write to the maker or its parts desk with the model, serial and part number, and ask the three things on the sheet. They may say yes to one, or no to all three.

  3. 3 Look for a match

    Tried the parts shops and used listings? Note it in row 3: the rungs below are still open. Search the exact part number with “used” or “new old stock”, meaning unused parts from old inventory. Try another brand’s equivalent too: some machine parts are standard parts under a different label. Check it against the fit table below before you buy.

  4. 4 Try a repair

    Tick what is wrong on the sheet. If the old part can be repaired and still do its job, you can stop here. If it carries a load or pressure, ask the maker first, and if it sits in a gas-fired or mains-powered machine, read the box at the end.

  5. 5 Have a new one made

    When no rung above works, a new part can be made from the old one. Take photos with a ruler beside it, write down the sizes where it meets the machine and what it fits onto, then ask a shop that makes one-off parts. To find one, search “reverse engineering” near you, or ask a repair shop for that machine.

  6. 6 Fix or retire

    Answer the last row with your own figures. If every rung is closed, retiring the machine is a fair answer.

Before you scrap it

Example, marked

Machine, model, serialAir cleaner, copied from the rating plate

The partBlower wheel, number molded on the hub

  • It is
  • Ticked: broken
  • worn
  • missing

1Keep it and name it

  • Ticked: Kept every piece
  • Ticked: photographed every number
  • Ticked: not glued or cleaned

Numbers foundthree digits on the hub (photo 2)

2Ask the maker

  • Asked for
  • Ticked: stock
  • Ticked: a newer part number
  • Ticked: a drawing or size sheet

Their answerno stock, no drawing

3Look for a match

Best matchanother brand’s wheel: holes fit, bore does not

  • Checked
  • Ticked: holes
  • Ticked: shaft or bore
  • height
  • Ticked: turning direction

4Try a repair

  • Crack only
  • Ticked: piece missing
  • hole worn

If a repair does the job, stop here.

5Have a new one made

  • Ticked: Photos with a ruler
  • Ticked: sizes written down
  • Ticked: what it fits noted

Shops askedtwo, photos and sizes sent

6Fix or retire

QuestionMy answer
New machine coststoo much
A week without ita rented tool
A rung still open?yes, rung 5

Retiring it is a fair answer too.

Before you scrap it · LOUEI 3D PRINT

Will the manufacturer share a drawing of a discontinued part?

A manufacturer may share a drawing of a discontinued part, so it is worth asking, but do not count on it.

Write to the maker with the model, serial and part number, and ask for stock, a newer part, and a drawing or dimension sheet a shop could work from. If they send a drawing, ask whether a shop may use it to make your part.

One woodworking-machine maker says it keeps parts for a time after a machine is discontinued, and will check whether a part from another machine can stand in. Under Canada’s Copyright Act, a maker usually owns the rights in its own drawings, so it is free to say no (general information, not legal advice). Asking costs you one email.

What if you cannot find the part number?

If you cannot find the part number, look on the machine’s rating plate, on the part itself and in the old manual, and keep the broken part as your record.

The model and serial number tell a parts desk which version of the machine you have, and even a part number you can only half read is worth writing down.

Line drawing of a workshop machine and the back of its blower wheel, showing where the rating plate, a molded number, a motor sticker and the old manual are.1423FRONT OF MACHINEPART, BACK SIDE
  1. Rating plate: model and serial; copy them exactly, letters and all.
  2. Molded number: may be small, on the back or the hub; light from the side helps.
  3. Motor sticker: a separate number for the motor; keep it apart from the part’s.
  4. Old manual: its parts diagram names each part by a reference number.

Photograph each number before you clean anything.

No number at all? Parts sellers then ask for photos from every side, its sizes and what it fits onto.

Will a generic part fit instead of the discontinued one?

A generic part fits only if it matches the old one wherever it meets the machine: the holes, the shaft or bore, the height and the way it faces or turns.

A replacement is not always a duplicate: a newer or look-alike part can change the mounting or the size. Lay the old and the new part side by side and go through the checks below before you buy.

What to check before a generic or used part replaces a discontinued one: compare the old and the new part on each point, and stop if any check fails.
CheckHow to compareStop if
Mounting holesCount them; measure each hole and the spacing centre to centreThe holes line up only after drilling or forcing
Shaft or boreMeasure the diameter, and any flat or key, on old and newThe new part slips, wobbles or needs force to go on
Height and reachLay both side by side, same face down; compare height, length and offsetsIt touches a neighbouring part or sits higher or lower
DirectionCheck which way it turns, faces or bends; left and right versions often differIt is a mirror image of the old one
The job it doesNote what the old part carried: a load, a spring, heat, water or powerThe new part is not sold for that job, or it is a safety part

Can a discontinued part be remade?

A discontinued part can often be made again from the broken one, as long as it does not carry pressure or a structural load.

Knobs, covers, spacers and simple brackets are the usual candidates, because they do not take heavy force. On a heavy machine, a part that takes high torque or impact, or carries the machine’s weight, is a question for the maker first. At LOUEI 3D PRINT, a remake can start from the broken part itself, a photo or your measurements. Here is how to have the discontinued part made again from the broken one.

One industrial maintenance guide warns that pressure-bearing or structural parts should not be printed unless the original maker can certify them as within its specifications. If your part is one of those, ask the maker first.

Start from the old part: a near match can share one size and miss two.

Same size, not the same part

Line drawing of a blower wheel seen face-on, with a D-shaped bore and blades leaning to the right.123
The old wheel: 1 a bore with one flat, 2 blades leaning this way, 3 this width.
Line drawing of a blower wheel of the same width, with a round bore and blades leaning to the left.123
A near match: 3 the same width, but 1 a round bore and 2 blades leaning the other way.

Is the machine worth fixing, or is it time to scrap it?

Whether a machine is worth fixing is a question for your own numbers, not a seller’s.

Ask three things. What would the same machine cost to replace today? What does each week without it cost you, in time, rented tools or lost work? Is any rung of the ladder still open: the maker, an equivalent, a used part, a repair or a remake?

If a rung is open and the first two answers are large, keep going: buying new is not always the cheaper route for a machine that still works. If every rung is closed, or the part is one that should not be copied, retiring the machine is a fair answer.

Before you contact any shop

Have these ready. Any shop will ask for most of them.

  • Photos: the whole part on plain paper, the same view with a ruler beside it, and the break up close.
  • The sizes you can measure, and what the part fits onto or into.
  • Where the part lives and what it does.
  • How many you need.
  • Any file or drawing you have, even an old one.

At LOUEI 3D PRINT you can start from anything: an idea, a sketch, a photo, CAD, measurements, the broken part itself or a previous order. We read STEP, STL, OBJ, IGES, DXF, PDF drawings and photographs.

When this is not a job for a shop

  • A brake, steering or other safety part is a case for a new part from a parts supplier, not a used one.
  • In Canada, the Motor Vehicle Safety Act sets standards for some vehicle equipment, so a vehicle safety part is not a casual copy.
  • If the part sits in a gas-fired or mains-powered machine: in BC, only qualified people employed by licensed contractors may do most gas and electrical work; homeowners need a permit for the rest.

Some parts cannot be reproduced: parts that are badly damaged, parts with missing geometry, and parts that need a certification we do not hold.

Written by the LOUEI 3D PRINT team. LOUEI 3D PRINT makes custom and replacement parts: 3D scanning and reverse engineering, FDM and resin 3D printing, molding and casting. Serving North America.

Back to the blog

Get a quote
LOUEI 3D PRINT

Get a quote

Tell us what you need — the review is free, and a person replies within one business day.

Opens your email app with everything filled in.